TechnicalData Sheet NC-AB No Clean Desoldering Wick June -2012 PRODUCT DESCRIPTION Specially processed copper braid is coated with a reduced volume of time tested Xersin 2005 halidfree synthetic resin NC-AB No Clean Desoldering Wick provides the following making the quantity of residue after use isignificantly less than product characteristics: the conventional desoldering wick. Xersin 2005 meets Bellcore TR-TSY 000078 issue 2, ANSI/IPCSF-818 and is rated Technology Desoldering Wick IPC-LR3CN. Application Soldering PCBs desoldered with NC-ABNo Clean Desoldering Wick will pass the MIL-P-28809ACleanliness Test without cleaning, NC-ABNo Clean Desoldering Wick is designed for static- free provided a No Clean Flux and a clean system and components desoldering applications and repair of PC boards, without the are used. PCBs willalso pass this test ifthey have been need for subsequent clean-up .It is formulated using a special cleaned after the soldering operation, provided they have been halide-free, vacuumised, no-clean, flux-coated copper braid for reworked using a No Clean flux in a clean environment. improved wicking .NC-ABNo Clean Desoldering Wick willnot loose its efficiencyeven after prolonged storage in humid conditions .It is made to remain flexibleand willnot flake. PACKAGING FEATURES AND BENEFITS NC-AB No Clean Desoldering Wick is supplied in static Faster and increased solder absorption dissipative plastic spools of 1.5m (5 ft.) each.This provides convenient application and protects the user from heat. Wound- on static dissipative spools Negligibleresidues which are non-corrosive, clear and NC-AB No Clean Desoldering Wick is packed in cartons non-hygroscopic containing five vacuum packed sleeves, each sleeve Heat stable coating containing ten static dissipative spools, for a total of fifty spools Vacuum packed per carton. Boards using NC-AB No Clean Desoldering Wick will NC-ABNo Clean Desoldering Wick is also availablein 100 feet meet the requirements of MIL-P-28809ACleanliness Econo- spools. Test without cleaning Approximate Width Label Color Code 1.88mm (0.074 in) 10% Green DIRECTIONS FOR USE Application: Lay NC-AB No Clean Desoldering Wick over the solder DATA RANGES requiring removal and place the soldering iron tip on top of the The data contained herein may be reported as a typical value copper braid. The braid and solder beneath willgradually heat and/or a range. Values are based on actual test data and are until the solder melts and is absorbed into the braid by capillary verified on a periodic basis . action. Remove the braid,cut off the solder- filledlength and dispose the leadcontaminated properly. GENERAL INFORMATION Sudden heat shock, which may be produced when using a For safe handling information on this product, consult the preheated vacuum desoldering tool, is prevented since the Material Safety Data Sheet (MSDS). braid is cold when itfirst comes into contact with the joint to be desoldered. Fume Hazards and Precautions The fumes resulting from use may irritate the nose and Special Properties respiratory organs. Avoid excessive inhaltion. Suitable fume extraction equipment should be used to extract fumes away NC-AB No Clean Desoldering Wick is supplied in static from the operators. When used at normal soldering dissipative spools conforming to both DOD Standard 1686and temperatures, the amount of leadfume given off is negligible. DOC Handbook 263 for static discharge protection. It also meets the decay rate provision of MIL-B-81705B.TDS NC-ABNo Clean Desoldering Wick, June -2012 Not for Product Specifications The technical information contained herein is intended for reference only. Please contact Henkel Technologies Technical Service for assistance and recommendations on specifications for this product. Conversions (C x 1.8)+ 32 =F kV/mm x 25.4 =V/mil mm /25.4 =inches m /25.4 =mil N x 0.225=lb N/mm x 5.71=lb/in N/mm x 145 =psi MPa x 145 =psi Nm x 8.851 = lbin Nm x 0.738=lbft Nmm x 0.142 =ozin mPas =cP Note The data contained herein are furnished for information only and are believed to be reliable.We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user s responsibility to determine suitability for the user s purpose of any production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In lightof the foregoing, Henkel Corporation and its affiliates (Henkel) specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Henkel products. Henkel specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by others or as a license under any Henkel patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications. Trademark usage Alltrademarks in this document are trademarks and/or registered trademarks of Henkel in the US and elsewhere. Reference 0.0 Americas Europe Asia +1.888.943.6535 +44.1442.278.000 +86.21.3898.4800 For the most direct access to local sales and technical support visit: www.henkel.com/electronics